AKTAKOM ASE-1101 is a durable soldering station with digital indication of soldering iron temperature. The temperature can be easily regulated with a rotary switch on the front panel.
This soldering station is especially recommended for transistors and microchips assembly produced in accordance with CMOS technology.
AKTAKOM ASE-1101 soldering station is ESD-safe. This is an important requirement that should be met since the absence of antistatic protection may cause the damage of valuable electronic components with electro static discharge.
AKTAKOM ASE-1101 soldering station (analog of JF-96ESD) is equipped with high-quality heating element that can be easily replaced. This heating element is covered with alumoceramic layer and inserted into ceramic housing. Such a reliable structure fully isolates the heating element from the environment effect and therefore protects the heating element from corrosion providing its high durability accordingly.
Multilayer (copper, steel and stannum) cover of the tip operating part has excellent thermal conduction and provides optimal high effective heat transmission. ASE-1101 soldering station is capable of assembling with 482-536°F / 250-280°C tip temperature completely guaranteeing the safety of printed conductors and electronic components.
Features
- The temperature control scheme provides high precision with accuracy not more than 2°F/-16.7°C from the set temperature
- The ergonomic design of a soldering iron handle provides convenient work; the handle covering is made of silicone rubber
- Power supply device is isolated from alternating current network
- Simplicity of calibration
- For the heating element supply the voltage of 24V is used
- Tip leakage is less than 0.4mV and the resistance is 0.5MΩ
- Sliding tray for sponge
- The temperature range: 392°F to 932°F / 200°C to 500°C
- High-quality and durable ceramic heating element produced in Japan provides quick heating, the insulation resistance is more than 100MΩ with the temperature of 750°F / 399°C
- ESD safe
Please note: ASE-1101 Soldering station is available in both (C°) and (F°) temperature settings. It is automatically set in (F°), however if you’d like it to be in (C°) please notify us in comments then making a purchase, or by contacting our sales department sales@tmatlantic.com
Specifications
Station
AC Input: 110-120V, 60Hz
Temperature Range: 390-930°F / 199-499°C
Dimensions: 6.7x4.7x4.1 in / 170x120x104 mm
Weight: 3.7lb/1.7kg
Soldering iron
Power Consumption: 24V/60W
Heating element: Ceramic heater
Leakage is less than 0.4mV
Included accessories
1. Power cable
2. Soldering iron holder
3. Soldering iron
4.Soldering Tip 90M-T-0.8C
5. Sliding tray for sponge
6. User manual
Safety instructions
Take care of yourself!
- Please read user manual carefully before using the instrument.
- Do not use the device if there is visible damage.
- Repair and maintenance of the device can be done only by a qualified specialist of the service center.
- Before connecting the instrument to the electrical network, observe all known precautions, and make sure that the grounding system is to avoid electric shock.
- Use only those accessories that are intended for use with this device.
- While working, do not touch the metal parts near the tip of the soldering iron.
- After completion of the work, it is necessary to install the soldering gun in the regular holder of the soldering gun.
Operation instructions
- Ensure working voltage matches your power supply before plugging into the station
- Carefully check any possible damage during transportation. Set temperature by moving "SET-READ" switch to "SET" position and rotate temperature control knob until the digital display reads the desired temperature. Then turn "SET-READ" switch to "READ" position. The station will maintain the preset temperature.
Frequently Asked Questions
What types of tips I can buy for soldering iron?
How to care and use of the soldering tip?
How to clean the tip?
Why a «de-tinned» tip fails to work?
What temperature should use for soldering?
How ASE-1101 Soldering Station is designed?
How to care and use of the soldering tip?
|
|
Tip’s temperature High soldering temperatures can degrade the tip. Use the lowest possible soldering temperature. The excellent thermal recovery characteristics ensure efficient and effective soldering event at low temperatures. This also protects the sensitive components from thermal damage. Cleaning Clean the tip regularly with a cleaning sponge, as oxides and carbides from the solder and flux can form impurities on the tip. These impurities can result in defective joints or reduce the tip's heat conductivity. When using the soldering iron continuously, be sure to loosen the tip and remove all oxides least once a week. This helps prevent reduction of the tip temperature. When not in use Never leave the soldering iron sitting at high temperature for long periods of time, as the tip's solder plating will be covered with oxide, which can greatly reduce the tip's heat conductivity. After use Wipe the tip and coat it with fresh solder. This helps to prevent tip oxidation.
Up
|
How to clean the tip?
|
|
Caution! Never file the tip to remove oxide.
- Set the temperature to 250°C.
- When the temperature stabilizes, clean the tip with the cleaning sponge and check the condition of the tip.
- If there is black oxide on the solder-plated portion of the tip, apply new solder (containing flux) and wipe the tip on the cleaning sponge. Repeat until the oxide is completely removed. Coat with new solder. The solder protects the tip from oxidation and prolongs the life of the tip.
- If the tip is deformed or heavily eroded, replace it with a new one.
Up
|
Why a «de-tinned» tip fails to work?
|
|
A de-tinned tip is one which cannot wet with solder. This exposes the plating to oxidation and degrades the heat transfer efficiency of the tip.
The de-tinning is caused by:
1) Failure to keep the tip covered with fresh solder while not in use.
2) High tip temperatures.
3) Insufficient melting in soldering operations.
4) Wiping the tip on dirty or dry sponges and rags (Always use a clean, wet, industrial grade, sulfur-free sponge).
5) Impurities in the solder, iron plating, or on the surfaces to be soldered.
Up
|
What temperature should use for soldering?
|
|
600 - 650°F (316 - 343°C) is a good place to start for lead-based solder and 650 - 700°F (343 - 371°C) for lead-free solder.
Note: if clots form, the temperature is too low.
Up
|
How ASE-1101 Soldering Station is designed?
|
|
ASE-1101 soldering station design is shown below:
Up
|
La estación para soldar AKTAKOM ASE-1101 es una estación de soldadura con protección antiestática e indicación digital de la temperatura del soldador. Se recomienda especialmente para los transistores de campo y el montaje microchips producidos de acuerdo con la tecnología CMOS
Ventajas:
- El esquema de control de temperatura proporciona una alta precisión con una precisión de no más de 2 ° F / -16.7 ° C de la temperatura
- El diseño ergonómico del mango soldador ofrece un trabajo cómodo, la cubierta mango está hecho de caucho de silicona
- La fuente de poder esta aislada de la corriente alterna
- Calibración fácil
- Para el elemento de calefacción se utiliza 24V
- El tipo de fuga es mnero a 0.4 mV y la resistencia es de 0.5 MΩ
- Bandeja deslizante para una esponja
- La alta calidad y durabilidad del elemento de calefacción de cerámica producido en Japón proporciona un calentamiento rápido y la resistencia de aislamiento es más de 100 MΩ con la temperatura de 750 ° F / 399 ° C
Tenga en cuenta: Que la estacion de soldar ASE-1101 esta disponible en dos versiones; Configurada para medir la temperatura en grados C° o en F°.
Normalmente viene configurada en grados F°, pero si la prefiere en grados C° por favor haganoslo saber por medio del Departamento de Ventas. Gracias
Back to the section
|
|
